All Kayak Fishing Forums

All Kayak Fishing Forums (http://www.allkayakfishing.com/forums/index.php)
-   All Kayak Fishing Chit-Chat (http://www.allkayakfishing.com/forums/forumdisplay.php?f=8)
-   -   ACE Hardware DIY cart (http://www.allkayakfishing.com/forums/showthread.php?t=324)

Fishyaker 10-08-2006 08:57 PM

ACE Hardware DIY cart
 
6 Attachment(s)
Well... this will be my first D.I.Y. and probably not the last. If I think something can be made cheaper with my own hands I usually will. I'll add pics tomorrow afternoon but here's a list of what I used.


1 Axle
1/2"x18" cold roll bar $2.79Attachment 36

2 1/2"x18" sch 80 pv $3.98
Cut to 11" for axle tube and cross barAttachment 37

2 1/2" collars with allen set screw $4.60

2 1/2"x8" sch 80 pv $2.18
For uprights from axle tube
Attachment 39

2 1/2"x6 sch 80 pv $1.78 (+2 @ .68 cheaper)
For kayak supports
Attachment 40

4 1/2" PVC tee fittings $1.16

2 5"x1" with 1/2"center wheels $5.98
Attachment 41

______
Total so far.... $22.47

I was originally going to use the scupper holes but had to revise. To finalize I need 2 more 1/2"x6 sch 80 pv @ 1.78 and 2 feet of pipe insulation (hopefully less than a few dollars).

Final product tomorrow evening.:stir

Added costs
2 1/2" pvc saddle clips for crossbar $1.70
2 more 1/2"x6 pv $1.10
6' pipe insulation $1.64

Final Total = $28.91 (I picked up the final items at Home Depot and prices were a bit cheaper :(). Maybe I should have gone there first and saved a few bucks.


Final product...Attachment 38

gone_fishing 10-17-2006 07:45 PM

Re: ACE Hardware DIY cart
 
How did the final product work out? Were any modifications necessary?
Hank

Fishyaker 10-17-2006 08:49 PM

Re: ACE Hardware DIY cart
 
Quote:

Originally Posted by gone_fishing (Post 897)
How did the final product work out? Were any modifications necessary?
Hank

Suprisingly, the final product works as I wanted with no modifications. I'm able to attach the cart using 2 18" bungy cords (one for each side crossing under the support and connected end to end through the scuppers).

Thing I might change if I were to do it again... using 2 more saddle clips instead of the tee fittings for the kayak support bars and 2 appropriate length PVs for the support bars themselves so that there is just one single bar instead of 2 shorter bars connected by the tee. The cart rolls fine on hard surface and is very stable (doesn't shift side to side or front/back).

Piranha 10-17-2006 09:34 PM

Re: ACE Hardware DIY cart
 
You were wise to revise. You've saved your yak! I think Hobie is the only yak that recommends a scupper cart! If I remember right, you have a cobra. You may wanna cut a pool noodle for cushion pads under the yak, but I suggest you give the ones you have a shakedown test. They might work just fine! I put my strap in the correct configuration on the cart skeleton, and attached it permanently to the cart in position using cable ties. You lean the cart at a 45 degree angle on the ground facing in the direction of the bow, place the yak on the cart,about 1/3 the distance forward from the stern, fasten the strap fairly snugly, then lift the back of the yak up quickly and the cart pops up into positiion. The cart will be in perfect position underneath the yak. No sweat! The bow will be on the ground and the stern in the air when you do this correctly. Finish retightening the strap in the upright position and you're ready to roll. If you ever go out with one of us, we'll demo it! Very simple and no crawling around on the sand under the yak! Piece o cake! Piranha out!:brews
PS, I use the nylon strap with the spring loaded clamp. It's always on the cart and in exactly the right place! THis strap is tighter than Bungees!

Fishyaker 10-17-2006 10:06 PM

Re: ACE Hardware DIY cart
 
I'll grab a pic with the cart mounted when I get a chance. How you described the sitting of the yak on the cart is how mine appears :-) Trying to get the right angle for the scuppers on the cobra would have just been a nightmare. With this solution I was able to eyeball the details on my workbench and it fits like a glove.

Piranha 10-22-2006 10:13 AM

Re: ACE Hardware DIY cart
 
:hello When you're haulin your yak back to the car, it's easier if you move anything heavy to directly over the wheels. That lightens the tongue weight you have to lift and puts the full moment of force on the ground! Pulling the yak that way is a piece of cake! Piranha


All times are GMT -7. The time now is 08:52 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.